CP(1) BSD Reference Manual CP(1)
cp - copy files
cp [-fip] [-R [-H | -L | -P]] source_file target_file cp [-fip] [-R [-H | -L | -P]] source_file ... target_directory
In the first synopsis form, the cp utility copies the contents of the source_file to the target_file. In the second synopsis form, the contents of each named source_file are copied to the destination target_directory. The names of the files themselves are not changed. If cp detects an at- tempt to copy a file to itself, the copy will fail. The options are as follows: -f For each existing destination pathname, remove it and create a new file, without prompting for confirmation, regardless of its permissions. This option overrides any use of -i. -H If the -R option is also specified, symbolic links on the command-line are followed. (Symbolic links encountered in the tree traversal are not followed.) -i Write a prompt to the standard error output before copying a file that would overwrite an existing file. If the response from the standard input begins with the character 'y', the file copy is attempted. -L If the -R option is also specified, all symbolic links are fol- lowed. -P If the -R option is also specified, no symbolic links are fol- lowed. -p Preserve in the copy as many of the modification time, access time, file flags, file mode, user ID, and group ID as allowed by permissions. If the user ID and group ID cannot be preserved, no error message is displayed and the exit value is not altered. If the source file has its set-user-ID bit on and the user ID cannot be preserved, the set-user-ID bit is not preserved in the copy's permissions. If the source file has its set-group-ID bit on and the group ID cannot be preserved, the set-group-ID bit is not preserved in the copy's permissions. If the source file has both its set-user-ID and set-group-ID bits on, and either the user ID or group ID cannot be preserved, neither the set-user-ID nor set-group-ID bits are preserved in the copy's permissions. -R If source_file designates a directory, cp copies the directory and the entire subtree connected at that point. Created direc- tories have the same mode as the corresponding source directory, unmodified by the process's umask. This option also causes symbolic links to be copied, rather than followed, and special files to be created, rather than being copied as normal files. However, cp copies hard linked files as separate files. To preserve hard links, use a utility such as pax(1) or tar(1) instead. For each destination file that already exists, its contents are overwrit- ten if permissions allow, but its mode, user ID, and group ID are un- changed. In the second synopsis form, target_directory must exist unless there is only one named source_file which is a directory and the -R flag is speci- fied. If the destination file does not exist, the mode of the source file is used as modified by the file mode creation mask (umask, see csh(1)). If the source file has its set-user-ID bit on, that bit is removed unless both the source file and the destination file are owned by the same user. If the source file has its set-group-ID bit on, that bit is removed un- less both the source file and the destination file are in the same group and the user is a member of that group. If both the set-user-ID and set- group-ID bits are set, all of the above conditions must be fulfilled or both bits are removed. Appropriate permissions are required for file creation or overwriting. Symbolic links are always followed unless the -R flag is set, in which case symbolic links are not followed, by default. The -H or -L flags (in conjunction with the -R flag) cause symbolic links to be followed as described above. The -H, -L, and -P options are ignored unless the -R op- tion is specified. In addition, these options override each other and the command's actions are determined by the last one specified. The cp utility exits 0 on success or >0 if an error occurred.
Make a copy of file foo named bar: $ cp foo bar Copy a group of files to the /tmp directory: $ cp *.txt /tmp Copy the directory junk and all of its contents (including any subdirec- tories) to the /tmp directory: $ cp -R junk /tmp
mv(1), rcp(1), umask(2), fts(3), symlink(7)
Historic versions of the cp utility had a -r option. This implementation supports that option; however, its use is strongly discouraged, as it does not correctly copy special files, symbolic links or FIFOs. The cp utility is expected to be IEEE Std 1003.2 ("POSIX.2") compatible.
A cp command appeared in Version 1 AT&T UNIX. MirOS BSD #10-current April 18, 1994 1
Generated on 2014-02-10 02:47:05 by $MirOS: src/scripts/roff2htm,v 1.79 2014/02/10 00:36:11 tg Exp $
These manual pages and other documentation are copyrighted by their respective writers;
their source is available at our CVSweb,
AnonCVS, and other mirrors. The rest is Copyright © 2002‒2014 The MirOS Project, Germany.
This product includes material provided by Thorsten Glaser.
This manual page’s HTML representation is supposed to be valid XHTML/1.1; if not, please send a bug report – diffs preferred.