RTADVD(8) BSD System Manager's Manual RTADVD(8)
rtadvd - router advertisement daemon
rtadvd [-dDfMRs] [-c configfile] interface ...
rtadvd sends router advertisement packets to the specified interfaces. The program will daemonize itself on invocation. It will then send router advertisement packets periodically, as well as in response to router sol- icitation messages sent by end hosts. Router advertisements can be configured on a per-interface basis, as described in rtadvd.conf(5). If there is no configuration file entry for an interface, or if the con- figuration file does not exist altogether, rtadvd sets all the parameters to their default values. In particular, rtadvd reads all the interface routes from the routing table and advertises them as on-link prefixes. rtadvd also watches the routing table. By default, if an interface direct route is added/deleted on an advertising interface and no static prefixes are specified by the configuration file, rtadvd adds/deletes the corresponding prefix to/from its advertising list, respectively. The -s option may be used to disable this behavior. Moreover, if the status of an advertising interface changes, rtadvd will start or stop sending router advertisements according to the latest status. Basically, hosts MUST NOT send Router Advertisement messages at any time (RFC 2461, Section 6.2.3). However, it would sometimes be useful to allow hosts to advertise some parameters such as prefix information and link MTU. Thus, rtadvd can be invoked if router lifetime is explicitly set zero on every advertising interface. The command line options are: -c Specify an alternate location, configfile, for the configuration file. By default, /etc/rtadvd.conf is used. -d Print debugging information. -D Even more debugging information is printed. -f Foreground mode (useful when debugging). Log messages will be dumped to stderr when this option is specified. -M Specify an interface to join the all-routers site-local multicast group. By default, rtadvd tries to join the first advertising in- terface appearing on the command line. This option has meaning only with the -R option, which enables routing renumbering proto- col support. -R Accept router renumbering requests. If you enable it, certain IP- sec setup is suggested for security reasons. This option is currently disabled, and is ignored by rtadvd with a warning mes- sage. -s Do not add or delete prefixes dynamically. Only statically con- figured prefixes, if any, will be advertised. Upon receipt of signal SIGUSR1, rtadvd will dump the current internal state into /var/run/rtadvd.dump. Use SIGTERM to kill rtadvd gracefully. In this case, rtadvd will transmit router advertisement with router lifetime 0 to all the interfaces (in accordance with RFC 2461 6.2.5).
The rtadvd program exits 0 on success, and >0 on failures.
/etc/rtadvd.conf The default configuration file. /var/run/rtadvd.pid contains the pid of the currently run- ning rtadvd. /var/run/rtadvd.dump The file in which rtadvd dumps its internal state.
The rtadvd command first appeared in the WIDE Hydrangea IPv6 protocol stack kit.
There used to be some text that recommended users not to let rtadvd ad- vertise Router Advertisement messages on an upstream link to avoid un- desirable icmp6(4) redirect messages. However, based on the later discus- sion in the IETF IPng working group, all routers should rather advertise the messages regardless of the network topology, in order to ensure reachability. MirOS BSD #10-current May 17, 1998 1
Generated on 2013-10-31 22:57:03 by $MirOS: src/scripts/roff2htm,v 1.77 2013/01/01 20:49:09 tg Exp $
These manual pages and other documentation are copyrighted by their respective writers;
their source is available at our CVSweb,
AnonCVS, and other mirrors. The rest is Copyright © 2002‒2013 The MirOS Project, Germany.
This product includes material provided by Thorsten Glaser.
This manual page’s HTML representation is supposed to be valid XHTML/1.1; if not, please send a bug report – diffs preferred.