CRASH(8) BSD System Manager's Manual CRASH(8)
crash - system failure and diagnosis
This section explains what happens when the system crashes and (very briefly) how to analyze crash dumps. When the system crashes voluntarily it prints a message of the form panic: why i gave up the ghost on the console and enters the kernel debugger, ddb(4). If you wish to report this panic, you should include the output of the ps and trace commands. If the 'ddb.log' sysctl has been enabled, anything output to screen will be appended to the system message buffer, from where it may be possible to retrieve it through the dmesg(8) command after a warm reboot. If the debugger command boot dump is entered, or if the debugger was not compiled into the kernel, or the debugger was dis- abled with sysctl(8), then the system dumps the contents of physical memory onto a mass storage peripheral device. The particular device used is determined by the 'dumps on' directive in the config(8) file used to build the kernel. After the dump has been written, the system then invokes the automatic reboot procedure as described in reboot(8). If auto-reboot is disabled (in a machine dependent way) the system will simply halt at this point. Upon rebooting, and unless some unexpected inconsistency is encountered in the state of the file systems due to hardware or software failure, the system will copy the previously written dump into /var/crash using savecore(8), before resuming multi-user operations.
The system has a large number of internal consistency checks; if one of these fails, then it will panic with a very short message indicating which one failed. In many instances, this will be the name of the routine which detected the error, or a two-word description of the inconsistency. A full understanding of most panic messages requires perusal of the source code for the system. The most common cause of system failures is hardware failure (e.g., bad memory) which can reflect itself in different ways. Here are the messages which are most likely, with some hints as to causes. Left unstated in all cases is the possibility that a hardware or software error produced the message in some unexpected way. no init This panic message indicates filesystem problems, and reboots are likely to be futile. Late in the bootstrap procedure, the system was unable to locate and execute the initialization process, init(8). The root filesystem is incorrect or has been corrupted, or the mode or type of /sbin/init forbids execution. trap type %d, code=%x, pc=%x A unexpected trap has occurred within the system; the trap types are machine dependent and can be found listed in /sys/arch/ARCH/include/trap.h. The code is the referenced address, and the pc is the program counter at the time of the fault is printed. Hardware flakiness will sometimes generate this panic, but if the cause is a kernel bug, the kernel debugger ddb(4) can be used to locate the in- struction and subroutine inside the kernel corresponding to the PC value. If that is insufficient to suggest the nature of the problem, more detailed examination of the system status at the time of the trap usually can produce an explanation. init died The system initialization process has exited. This is bad news, as no new users will then be able to log in. Rebooting is the only fix, so the system just does it right away. out of mbufs: map full The network has exhausted its private page map for network buffers. This usually indicates that buffers are being lost, and rather than allow the system to slowly degrade, it reboots im- mediately. The map may be made larger if necessary. That completes the list of panic types you are likely to see.
When the system crashes it writes (or at least attempts to write) an im- age of memory, including the kernel image, onto the dump device. On re- boot, the kernel image and memory image are separated and preserved in the directory /var/crash. To analyze the kernel and memory images preserved as bsd.0 and bsd.0.core, you should run gdb(1), loading in the images with the follow- ing commands: # gdb GNU gdb 6.1 Copyright 2004 Free Software Foundation, Inc. GDB is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. Type "show copying" to see the conditions. There is absolutely no warranty for GDB. Type "show warranty" for details. This GDB was configured as "i386-unknown-openbsd3.6". (gdb) file /var/crash/bsd.0 Reading symbols from /var/crash/bsd.0...(no debugging symbols found)...done. (gdb) target kvm /var/crash/bsd.0.core After this, you can use the where command to show trace of procedure calls that led to the crash. For custom-built kernels, it is helpful if you had previously configured your kernel to include debugging symbols with 'makeoptions DEBUG=-ggdb' (see options(4)) (though you will not be able to boot an unstripped ker- nel since it uses too much memory). In this case, you should use bsd.gdb instead of bsd.0, thus allowing gdb(1) to show symbolic names for ad- dresses and line numbers from the source. Analyzing saved system images is sometimes called post-mortem debugging. There are a class of analysis tools designed to work on both live systems and saved images, most of them are linked with the kvm(3) library and share option flags to specify the kernel and memory image. These tools typically take the following flags: -N system Takes a kernel system image as an argument. This is where the symbolic information is gotten from, which means the image cannot be stripped. In some cases, using a bsd.gdb version of the kernel can assist even more. -M core Normally this core is an image produced by savecore(8) but it can be /dev/mem too, if you are looking at the live system. The following commands understand these options: fstat(1), netstat(1), nfsstat(1), ps(1), systat(1), w(1), dmesg(8), iostat(8), kgmon(8), pstat(8), slstats(8), trpt(8), vmstat(8) and many others. There are ex- ceptions, however. For instance, ipcs(1) has renamed the -M argument to be -C instead. Examples of use: # ps -N /var/crash/bsd.0 -M /var/crash/bsd.0.core -O paddr The -O paddr option prints each process' struct proc address, but with the value of KERNBASE masked off. This is very useful information if you are analyzing process contexts in gdb(1). You need to add back KERNBASE though, that value can be found in /usr/include/$ARCH/param.h. # vmstat -N /var/crash/bsd.0 -M /var/crash/bsd.0.core -m This analyzes memory allocations at the time of the crash. Perhaps some resource was starving the system?
The following example should make it easier for a novice kernel developer to find out where the kernel crashed. First, in ddb(4) find the function that caused the crash. It is either the function at the top of the traceback or the function under the call to panic() or uvm_fault(). The point of the crash usually looks something like this "function+0x4711". Find the function in the sources, let's say that the function is in "foo.c". Go to the kernel build directory, i.e., /sys/arch/ARCH/compile/GENERIC. Do the following: # rm foo.o # make -n foo.o | sed 's,-c,-g -c,' | sh # objdump -S foo.o | less Find the function in the output. The function will look something like this: 0: 17 47 11 42 foo %x, bar, %y 4: foo bar allan %kaka 8: XXXX boink %bloyt etc. The first number is the offset. Find the offset that you got in the ddb trace (in this case it's 4711). When reporting data collected in this way, include ~20 lines before and ~10 lines after the offset from the objdump output in the crash report, as well as the output of ddb(4)'s "show registers" command. It's impor- tant that the output from objdump includes at least two or three lines of C code.
If you are sure you have found a reproducible software bug in the kernel, and need help in further diagnosis, or already have a fix, use sendbug(1) to send the developers a detailed description including the entire ses- sion from gdb(1).
gdb(1), sendbug(1), ddb(4), reboot(8), savecore(8) MirOS BSD #10-current February 23, 2000 2
Generated on 2013-10-31 22:57:03 by $MirOS: src/scripts/roff2htm,v 1.77 2013/01/01 20:49:09 tg Exp $
These manual pages and other documentation are copyrighted by their respective writers;
their source is available at our CVSweb,
AnonCVS, and other mirrors. The rest is Copyright © 2002‒2013 The MirOS Project, Germany.
This product includes material provided by Thorsten Glaser.
This manual page’s HTML representation is supposed to be valid XHTML/1.1; if not, please send a bug report – diffs preferred.